uConnect
Ubiquitous Connect
©2020 All rights reserved by Uconnect
Bluetooth V5.0 BLE RS-422/485 adapter
New Bluetooth V5.0 BLE RS-422/485 adapter
Model: S2B5485E (External Dipole Antenna)
Model: S2B5485I (Internal Antenna) (Option)
1. Baud Rate: Supports 1.2/2.4/4.8/9.6/19.2/38.4/57.6/115.2/230.4/460.
8/921.6 Kbps (Default: 9600 bps)
3. Parity: none(Default)/even, w/o Odd
4. Stop bit: 1 only
5. Data bit: 8 only
6. Range: 70 m ,in open space for reference only
7. Signal: TxD, RxD, GND, CTS/RTS (H/W Flow control)
8. RS-232 Interface: D-SUB 9-pin male
9. Antenna Gain: max. 2 dBm
10. Profiles: GATT Serial
11. Frequency: 2.400 to 2.4835 GHz
12. Tx. Power: Max. +4 dBm
13. Rx. Sensitivity: -96 dBm typical
14. Power Supply: 5~40 VDC
15. Current Consumption: max. 30 mAh (for reference)
16. Operation Temperature: –40 °C to +85 °C
17. Dimensions: 81.6 mm (L) x 31.75 mm (W) x 17 mm (H)
Specifications:
E-Mail:
Sales@uconnect.com.tw
Configuration Interfaces: (Please choose 1 of 3 ways)
1. DIP Switch on the Rear side (Default, please refer the pin no. on the above
picture.)
Configuration APP:
1. Baud rate, Parity, Stop bit, Flow control
2. Data communication test
3. Enable central to link peripheral
Male DB9:
Top View:
Rear View:
The Bluetooth V5.0 BLE RS422/485 adapter
supports the iOS, Android, Windows or etc.. The
central or peripheral will be configured by the
command, DIP switch or APP. The HW or FW will
be customized by the requirements, please contact
us. The Modbus of RS-485 support the check sum
on slave side.
2. AT command via RS-232 interface (Please check the user manual)
3. APP via GATT service
UUID_1800_SERV = ("00001800-0000-1000-8000-00805F9B34FB")
UUID = 2A00, Device name, Default: BLE232
UUID_180A_SERV = ("0000180A-0000-1000-8000-00805F9B34FB")
UUID= 2A26, Firmware version, Format: x.x.x, ASCII/read only
UUID= 2A24, BLE version, Format: x.x, ASCII/read only, Value: 4.2 or 5.0
UUID_BLE_SERV = ("0003ABCD-0000-1000-8000-00805F9B0131") (Self defined UUID)
UUID_BLE5DATA = ("00031201-0000-1000-8000-00805f9b0130"), Data from
BLE232_TxData (Notification)
UUID_BLE5SENT = ("00031202-0000-1000-8000-00805f9b0130"),//Data to
BLE232_RxData max244bytes/package(write only)
UUID_BLE5ADDR = ("00031204-0000-1000-8000-00805f9b0130"), Target Peripheral
Mac. Address, 6bytes,(read/write)
UUID_BLE5NAME = ("00031205-0000-1000-8000-00805f9b0130"), Device name, Max.
15bytes, UTF-8,(read/write)
UUID_BLE5PIN = ("00031206-0000-1000-8000-00805f9b0130"), Pin code, 6bytes,
(read/write)
UUID_BLE5RBT = ("00031210-0000-1000-8000-00805f9b0130");Reboot, 2bytes,
(read/write)
UUID_BLE5CONF = ("00031203-0000-1000-8000-00805f9b0130"), Configuration,
4bytes, (read/write)
Byte0 (Read Only)
|
Byte1
|
Byte2
|
Byte3
|
Product model
|
Baud Rate
|
N/A
|
Port setting
|
0xAA: RS232 0xAF: RS485/422
|
unit: bps 0x00: 1200 0x01: 2400 0x02: 4800 0x03: 9600 0x04: 19200 0x05: 38400 0x06: 57600 0x07: 115200 0x08: 230400
|
|
bit 0: Parity (0: NONE 1: EVEN) bit 1: Flow control (0: Disabled 1: Enabled) (for RS232 model Only) bit 2: N/A bit 3: Port Type (0: RS485 1: RS422) (Available on RS485 model only) bit 4: BLE Role (0: Peripheral 1: Central) (indication Only) bit 5: ControlSet (0: set by APP or command 1: set by 9P switch) (indication Only)
|
|